International conference proceedings - Teramoto Koji

Division display >> ／  All the affair displays  1 - 34 of about 34

  1. Research on estimation of clamping force decrease due to workpiece rigidity reduction in machining

    Shunya TAGUCHI, Koji TERAMOTO, Naruki SHOJI，Proc. of the 27th International Conference on Mechatronics Technology，2024.11

  2. Research on measuring point selection for strainbased on-machine estimation of workholding states

    Yu YAN, Koji TERAMOTO, Naruki SHOJI and Hiroki MATSUMOTO，Proc. of the 20th International Conference of Precision Engineering，Article Number:OS05-02，2024.10，Sendai

  3. Research on Measuring Point Selection for Workpiece Thermal Monitoring

    Mengmeng YANG, Koji TERAMOTO, Feng ZHANG，Proc. of The 10th Int. Conf. on Leading Edge Manufacturing in 21st Century，2021.11

  4. Modelling of fixturing force reduction caused by workpiece rigidity change

    Yuya HIBINO and Koji TERAMOTO，Proc. of The 10th Int. Conf. on Leading Edge Manufacturing in 21st Century，2021.11

  5. Proposal of a Framework for Empirical Modelling of Complex Machining Phenomena

    Adirake Chainawaku, Koji Teramoto, Zejian Wu, Takahiro Katsube，Proc of 18th International Conference on Precision Engineering，Article Number: B-1-2，JSPE，2020.11，Virtual

  6. Analysis of the Effect of Machining Sequence on Machining Error Considering Workpiece Rigidity Change

    Yutaro NAKAO and Koji TERAMOTO，JSME 2020 Conference on Leading Edge Manufacturing/Materials and Processing LEMP2020，Article Number:LEMP2020-8581，JSME，2020.06，Virtual

  7. On-Machine Estimation of Workpiece Deformation for Thin-Walled Parts Considering Fixture Clamping Sequence

    Jingkai Zeng, Koji Teramoto, Dongjin Wu, Hiroki Matsumoto，JSME 2020 Conference on Leading Edge Manufacturing/Materials and Processing LEMP2020，Article Number:LEMP2020-8570，JSME，2020.06，Virtual

  8. Proposal for a workpiece monitoring framework for accurate end-milling

    Dongjin Wu, Koji Teramoto, Jingkai Zeng，8th International Conference of Asian Society for Precision Engineering and Nanotechnology，Article Number:D20，2019.11，Matsue

  9. On-machine Estimation of Workholding Situation for Thin-walled Parts

    Jingkai Zeng, Koji Teramoto, Dongjin Wu，8th International Conference of Asian Society for Precision Engineering and Nanotechnology，Article Number:D21，2019.11，Matsue

  10. Research on estimation of machining error factors for accuracy assured machining

    Yutaro NAKAO and Koji TERAMOTO，oint Symposium on Mechanical Industrial Engineering and Robotics 2019 (MIER2019)，(p.23 ～ 24)，Article Number:S22，2019.07，Muroran

  11. Experimental investigation on uncertainties of workholding process in end-milling

    Koji TERAMOTO, Shyuuhei KUTOMI, JingKai ZENG and Dongjin WU，Proceedings of the 2018 International Symposium on Flexible Automation (ISFA2018)，Article Number:S046，2018.07，Kanazawa

  12. Research on mechanistic modeling of machining error for model-based elastomer end-milling

    Zejian WU, Koji TERAMOTO，Proceedings of The 9th International Conference on Leading Edge Manufacturing in 21st Century ，Article Number:E05，2017.11，Hiroshima, Japan

  13. Development of Body-powered Prosthetic Hand for Non-dominant Hand Use

    Yutaro MATSUI and Koji TERAMOTO, ，Proceedings of 21st International Conference on Mechatronics Technology，(p.218 ～ 221)，2017.10， Ho Chi Minh City, Vietnam

  14. A Proposal of Selection Method for Temperature Measurement in End-Milling

    Dngjin WU and Koji TERAMOTO，Proceedings of the 16th International Conference on Precision Engineering (ICPE2016)，2016.11，Hamamatsu

  15. Study of rapid on-machine shape measurement for accuracy assured machining

    Kentaro OTA, Koji TERAMOTO, and Ryota HAYASHI，Proc. of the 8th International Conference on Leading Edge Manufacturing in 21st Century，(p.A03 ～ )，JSME，2015.10，京都

  16. Analysis of cutting force in elastomer endmilling

    Koji Teramoto, Takahiro Kunishima and Yutaro Furuya，Proc. of 15th International Conference on Precision Engineering (ICPE2014)，(p.599 ～ 602)，JSPE，2014.07，石川

  17. In-process Observation of Workpiece Deformation in Elastomer Endmilling

    Koji TERAMOTO, Shohei KUDO and Yuichiro FURUYA，Proc. of The 7th International Conference on Leading Edge Manufacturing in 21st Century，(p.259 ～ 262)，JSME，2013.11，宮城

  18. Application of ultraprecision microgrooves to dental implant and blood inspection

    Tohru Ishida, Koji Teramoto, Keiichi Nakamoto and Yoshimi Takeuchi，Proceedings of CIRP BioManufacturing 2013，2013.02，東京

  19. Japan --Thailand Joint Seminar and International Symposium on Mechanical and Industrial Engineering Between Muroran Institute of Technology and Chiang Mai University ­ MIER2012

    Toshiharu Kazama, Naohiko Hanajima, Koji Teramoto, Tomonori Yuasa, Yasuhiro Osafune, Hiroyuki Fujiki and Wichai Chattinnawat，Japanese Society for Engineering Education 60th Annual Conference & Exposition，JSEE，2012.08，東京

  20. Development of a robotic medical endoscope for single-handed operation

    Keitarou Morita and Koji Teramoto，Proceedings of Joint Symposium on Mechanical - Industrial Engineering, and Robotics 2012，(p.41 ～ )，2012.01，Muroran

  21. Experimental investigation of machining error in elastomer endmilling

    Kazuhisa YABUKI and Koji TERAMOTO，Proceedings of Joint Symposium on Mechanical - Industrial Engineering, and Robotics 2012，(p.32 ～ )，2012.01，Muroran

  22. Proposal of development scheme for novel functional prosthetic hands

    Koji TERAMOTO，Proceedings of Joint Symposium on Mechanical - Industrial Engineering, and Robotics 2012，(p.37 ～ )，2012.01，Muroran

  23. On-machine Estimation of Thin-structured Parts Deformation

    Wataru KONNO and Koji TERAMOTO，Proc. of 14th International Conference on Mechatronics Technology (ICMT2010)，(p.A27 ～ )，2010.11，大阪

  24. Development of digital prototyping environment for tailor-made body-powered prosthesis

    K. Teramoto and S. Yokota，Proc. of Thailand-Japan International Symposium in Industrial Engineering, Mechanical Engineering and Robotics 2010 (TJIEME-CMU-MuroranIT-2010)，(p.19 ～ 22)，2010.11，チェンマイ

  25. Proposal of fabrication method for complicated and hollow shape FRP parts

    M. Ishitani and K. Teramoto，Mechanical Engineering and Robotics 2010 (TJIEME-CMU-MuroranIT-2010)，(p.15 ～ 18)，2010.11，チェンマイ

  26. Analysis of Machining Error in soft-objects end-milling

    Koji TERAMOTO and Daisuke WATANABE，Proceedings of the 2010 International Symposium on Flexible Automation (ISFA2010)，(p.CD-ROM ～ )，システム制御情報学会，ASME，2010.07，東京

  27. Development of a Process Planning System for 3+2 Control Rough Milling

    Takeshi UMEHARA, Keiichi NAKAMOTO, Tohru ISHIDA, Koji TERAMOTO, Yoshimi TAKEUCHI，Proceedings of the 2010 International Symposium on Flexible Automation (ISFA2010)，(p.CD-ROM ～ )，システム制御情報学会，ASME，2010.07，東京

  28. A framework for machining of soft objects

    Koji TERAMOTO, Yuichi KUROISHI and Masataka YAMASHITA，Proceedings of the 5th International Conference on Leading Edge Manufacturing in 21st Century(LEM21)，(p.365 ～ 368)，JSME，2009.12，大阪

  29. A proposal of fixturing variation model for low-rigidity parts machining

    Koji TERAMOTO，Proceedings of the 2008 International Symposium on Flexible Automation（ISFA2008)，(p.CD-ROM ～ )，システム制御情報学会，ASM，2008.06，アトランタ

  30. A Framework of Compositional Machining Simulation for Versatile Machining Simulation

    Koji Teramoto, Jun'ichi Kaneko, Tohru Ishida, Yoshimi Takeuchi，Proc. the 4th Int. Conf. on Leading Edge Manufacturing in 21st Century，(p.461 ～ 464)，JSME，2007.11，Fukuoka

  31. A fundamental study on the compositional machining simulation

    Koji Teramoto, Jun'ichi Kaneko, Tohru Ishida, Yoshimi Takeuchi，Proceedings of 8th International Conference on Progress of Machining Technology (ICPMT2006)，(p.317 ～ 320)，2006.11，松江

  32. Phased Construction of CAM System for Newly Developed Machine Tools

    Koji TERAMOTO, Hirofumi YONEDA, Yasufumi UEDA, Tohru ISHIDA, Yoshimi TAKEUCHI, Tetsuro SHIBUKAWA，Proceedings of the 2006 International Symposium on Flexible Automation (ISFA2006)，(p.420 ～ 423)，2006.06

  33. 5-Axis Control Tool Path Generation Using Curved Surface Interpolation

    K. Teramoto, M. Morikawa, T. Ishida, Y. Takeuchi，Proceedings of 2nd CIRP International Conference on High Performance Cutting，2006.06，バンクーバー

  34. Thermal state visualization of machining workpiece by means of sensor-configured heat conductive simulation

    Teramoto, K. Tanaka, R., Ishida, T.and Takeuchi, Y.，Proceedings of the 3rd International Conference on Leading Edge Manufacturing in 21st Century(LEM21)，(p.921 ～ 926)，JSME，2005.10

< PREV - NEXT >

  • 1
To the head of this page.▲